光立方3D8 2803+573.源程序 HEX C 仿真电路图 一整套

一整套光立方8*8*8 所需的文件 包括头文件 源程序 仿真电路图 使用2083和573 构成的电路

#include 
 #include 
#define uchar unsigned char

#define uint unsigned int

uchar display[8][8];

/*rank:A1234I心U*/

uchar code table_cha[8][8]={0x510x510x510x4a0x4a0x4a0x440x440x180x1c0x180x180x180x180x180x3c0x3c0x660x660x300x180xc0x60xf60x3c0x660x600x380x600x600x660x3c0x300x380x3c0x3e0x360x7e0x300x300x3c0x3c0x180x180x180x180x3c0x3c0x660xff0xff0xff0x7e0x3c0x180x180x660x660x660x660x660x660x7e0x3c};

/*the “ideasoft“*/

uchar code table_id[40]={0x810xff0x810x000xff0x810x810x7e0x000xff0x890x890x000xf80x270x270xf80x000x8f0x890x890xf90x000xff0x810x810xff0x000xff0x090x090x090x010x00x010x010xff0x010x010x00};

/*railway*/

uchar code dat[128]={0x00x200x400x600x800xa00xc00xe00xe40xe80xec0xf00xf40xf80xfc0xdc0xbc0x9c0x7c0x5c0x3c0x1c0x180x140x100xc0x80x40x250x450x650x850xa50xc50xc90xcd0xd10xd50xd90xb90x990x790x590x390x350x310x2d0x290x4a0x6a0x8a0xaa0xae0xb20xb60x960x760x560x520x4e0x6f0x8f0x930x730x6f0x8f0x930x730x4a0x6a0x8a0xaa0xae0xb20xb60x960x760x560x520x4e0x250x450x650x850xa50xc50xc90xcd0xd10xd50xd90xb90x990x790x590x390x350x310x2d0x290x00x200x400x600x800xa00xc00xe00xe40xe80xec0xf00xf40xf80xfc0xdc0xbc0x9c0x7c0x5c0x3c0x1c0x180x140x100xc0x80x4};

/*railway 2*/

uchar code dat2[28]={0x00x200x400x600x800xa00xc00xe00xe40xe80xec0xf00xf40xf80xfc0xdc0xbc0x9c0x7c0x5c0x3c0x1c0x180x140x100xc0x80x4};

/*railway 3*/

uchar code dat3[24]={0x000x010x020x030x040x050x060x160x260x360x460x560x660x650x640x630x620x610x600x500x400x300x200x10};

/*3p char*/

uchar code table_3p[3][8]={0xff0x890xf50x930x930xf50x890xff0x0e0x1f0x3f0x7e0x7e0x3f0x1f0x0e0x180x3c0x7e0xff0x180x180x180x18};

/*initializtion

That is to initialize the program .

It is write to set the timer in c52 mcu.

So the program can renovate the led_3d_cube in fixed time use the interrupt function.*/

void sinter（）

{

         IE=0x82;

         TCON=0x01;

         TH0=0xc0;

         TL0=0;

         TR0=1;

}

void delay5us（void）   //误差 -0.026765046296us STC 1T 22.1184Mhz
{
    unsigned char ab;
    for（b=7;b>0;b--）
        for（a=2;a>0;a--）;
}

void delay（uint i）

{                                                                                                     

         while （i--）{
		 delay5us（）;}//12t的mcu 注释这个延时即可
}

/*To judge the num bit*/

uchar judgebit（uchar numuchar b）

{

         char n;

         num=num&（1<
         if （num）

         n=1;

         else

         n=0;

         return n;

}

/*To figure out the round number*/

uchar abs（uchar a）

{

         uchar b;

         b=a/10;

         a=a-b*10;

         if （a>=5）

         b++;

         return b

 属性            大小     日期    时间   名称
----------- ---------  ---------- -----  ----

     文件      73644  2012-02-04 20:27  光立方2803+573\001.jpg

     文件      64613  2012-02-04 20:27  光立方2803+573\002.jpg

     文件      56906  2012-12-01 19:28  光立方2803+573\8X8X8

     文件      38266  2012-02-06 21:50  光立方2803+573\8X8X8.c

     文件      24769  2012-12-01 19:28  光立方2803+573\8X8X8.hex

     文件         42  2012-12-01 19:28  光立方2803+573\8X8X8.lnp

     文件      77062  2012-12-01 19:28  光立方2803+573\8X8X8.LST

     文件      67197  2012-12-01 19:28  光立方2803+573\8X8X8.M51

     文件      75206  2012-12-01 19:28  光立方2803+573\8X8X8.OBJ

    .......       975  2012-02-25 19:43  光立方2803+573\8X8X8.opt.bak

     文件        459  2012-12-02 00:27  光立方2803+573\8X8X8.plg

    .......      2143  2012-02-25 19:43  光立方2803+573\8X8X8.Uv2.bak

    .......     57309  2012-12-02 00:27  光立方2803+573\8X8X8.uvopt

    .......     13235  2012-12-02 00:27  光立方2803+573\8X8X8.uvproj

    .......         0  2012-02-25 19:42  光立方2803+573\8X8X8_Uv2.Bak

     文件    1004806  2012-02-04 20:33  光立方2803+573\yuanli.jpg

     目录          0  2012-12-02 00:27  光立方2803+573

     文件     604255  2013-01-30 15:45  原理图new.pdf

----------- ---------  ---------- -----  ----

              2160887                    18